J-Log.eu - Forum

JLF ------ SPAM Bots! Bitte nach Registrierung eine Email an mich zur Freischaltung! / After registration drop me an email please for clearing! ===Nenne/name the NICK you used to register with!=== Email address: -> http://j-log.eu/impressum
Aktuelle Zeit: 13. Mär 2020, 03:50

Alle Zeiten sind UTC + 1 Stunde




   [ 5 Beiträge ] 
Autor Nachricht
 Betreff des Beitrags: Advice on how to power luxeon alarm
Verfasst: 2. Nov 2011, 10:31 

Registriert: 2. Nov 2011, 10:08
Beiträge: 2
Hello, nice forums ! I am very happy with my J-Log and with normal LED alarms.

But I've got some Luxeon LED that I wanted to use instead, so I made a new alarm device circuit with stronger transistor (BD243) and it works great with my current-limiting bench PSU and this Luxeon LED (this one: http://www.sparkfun.com/products/9634), current is about 300mA at 3.7V and visibility is much better. Now, how to power it on-board ? If I was to use a single-cell LiIon/LiPo do I need current limiting circuit so I won't blow out my LED ? Or am I safe because of the pulses ?

Thanks in advance


Nach oben
   
 
Verfasst: 2. Nov 2011, 10:52 
The Madman from Laboratory 4

Registriert: 8. Jun 2011, 14:28
Beiträge: 4760
Hi!

You know that? http://62.153.249.80/jlog/jlog2-en/alarm-devices-for-jlog2-v3-2up

Do you have a series resistor in the path collector-BD243--Luxeon?
Well, also with no resistor the pulses in mode "flash" are short enough (32ms) to be able to drive a power LED by overcurrent without burning it.

But: Attention! If you flash the logger or disconnect the alarm device (control) from the logger the LED will be ON continuously! If you do not use an optocoupler in front then the 10k resistor here http://62.153.249.80/jlog/wp-content/uploads/2011/06/Alarm_device_JLog2_v3.2up-2.jpg will avoid that. The only disadvantage is that there is no alarm in case of the alarm device is disconnected from the logger or the logger lost its supply voltage. But that kind of alarm w'd be anyway a continuously burning LED, "burning" in the meaning of the word, perhaps. (In case there is no current delimiting series resistor.)

Series resistor collector-LED: Ualarm (supply voltage of the alarm device) minus forward voltage (of the LED, check out the specs) devided by LED current (R=U/I).

_________________
Tom


Nach oben
   
 
Verfasst: 2. Nov 2011, 11:05 
The Madman from Laboratory 4

Registriert: 8. Jun 2011, 14:28
Beiträge: 4760
Modified the above post, --> refresh!

_________________
Tom


Nach oben
   
 
Verfasst: 2. Nov 2011, 12:18 

Registriert: 2. Nov 2011, 10:08
Beiträge: 2
Thanks for quick reply !

dl7uae hat geschrieben:

Yes, this is what I am trying to understand

dl7uae hat geschrieben:
Do you have a series resistor in the path collector-BD243--Luxeon?
Well, also with no resistor the pulses in mode "flash" are short enough (32ms) to be able to drive a power LED by overcurrent without burning it.

No, but I think I will add one to be safe

dl7uae hat geschrieben:
But: Attention! If you flash the logger or disconnect the alarm device (control) from the logger the LED will be ON continuously! If you do not use an optocoupler in front then the 10k resistor here http://62.153.249.80/jlog/wp-content/uploads/2011/06/Alarm_device_JLog2_v3.2up-2.jpg will avoid that. The only disadvantage is that there is no alarm in case of the alarm device is disconnected from the logger or the logger lost its supply voltage. But that kind of alarm w'd be anyway a continuously burning LED, "burning" in the meaning of the word, perhaps. (In case there is no current delimiting series resistor.)


So we cannot avoid 'open-input=steady on' unless we skip the opto ?
How safe is it to skip the opto ?


Nach oben
   
 
Verfasst: 2. Nov 2011, 13:59 
The Madman from Laboratory 4

Registriert: 8. Jun 2011, 14:28
Beiträge: 4760
It is not directly unsafe w/o opto. So you may go on the no-opto version with the 10k resistor providing that the LED is off with an open input.

_________________
Tom


Nach oben
   
 
Beiträge der letzten Zeit anzeigen:  Sortiere nach  
   [ 5 Beiträge ] 

Alle Zeiten sind UTC + 1 Stunde


Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 1 Gast


Du darfst keine neuen Themen in diesem Forum erstellen.
Du darfst keine Antworten zu Themen in diesem Forum erstellen.
Du darfst deine Beiträge in diesem Forum nicht ändern.
Du darfst deine Beiträge in diesem Forum nicht löschen.
Du darfst keine Dateianhänge in diesem Forum erstellen.

Suche nach:
Gehe zu:  
Powered by phpBB® Forum Software © phpBB Group
Deutsche Übersetzung durch phpBB.de